The Allis Chalmers HD6 crawler dozer and HD6G
crawler loaders used the same steering clutches. As long as your steering clutches are the
dry steering clutches, PRIOR TO SERIAL NUMBER 14484 AND UP!!!..., this information will
apply. They originally used qty 10 each of the fiber and qty 10 each of the steel discs.
You can repair your clutches with either the original fiber discs or upgrade your clutches
with bimetallic discs, which give longer life and are less prone to bonding to the steel
discs and seizing up your clutch pack. With the bimetallic discs, you will not have
any more broken teeth on your friction plates!
To make the upgrade and conversion to the bimetallic friction discs, you need qty 12
bimetallic discs and 12 steel plates. If your steel plates are good, you only need to
purchase two steel plates to go with the 12 bimetallic discs per clutch. Upgrading to the bimetallic disc pack does cost more and
you are the only one that can make the decision between the two different styles of clutch
packs. For some people the labor and inconvenience involved in future steering
clutch repair is not a consideration, while for others it is very important. For less than
a $250 difference in cost, you will end up with a superior clutch, much fewer
headaches, and less labor in the future if you convert to the BiMetallic discs.
ORDERING INFO:
 We can usually ship on the same day any items we have in
stock that do not have to be pulled from a machine. We are set up to offer the
payment choices of either Visa, Master Card, or the PayPal option (to the account of webmaster@tractorparts.com)
Al items below are in stock and if you would
like to get any of them on the way just let us know! If you are in the US you may
call 1-800-531-9021 or if you are outside the US, 1 208 342 8911. You may also
email steeringclutch@gmail.com
for orders/questions.
Our hours are Monday through Friday from 10 am
Eastern Time to 6 pm Eastern Time (8 am Mtn Time to 4 pm Mtn Time). We are located
20 miles east of Boise, Idaho.
CLUTCH PACK OPTIONS
(10) DRY TYPE
CLUTCH FIBER FRICTION AND (10)
STEEL PLATES = $390.00
(12) DRY TYPE CLUTCH BIMETALLIC FRICTIONS AND (12) STEEL PLATES = $636.00
Fiber Friction Discs ...new after market 18.00 ea
044585--->066360
044478 (70044478)
 Steel separator plates
041781 --->
70624562... 21.00
ea
Bimetallic Friction discs 70609699--->057375 (70057375) 32.00
ea
 OIL TYPE BIMETALLIC FRICTION DISCS 70624561
42.00 EA
12 USED PER CLUTCH These oil type friction
discs also fit the HD6, HD7, HD11, HD12, AND 8G crawlers.
OIL TYPE BIMETALLIC CLUTCH PACK of 12 bimetalllics
and 12 steels = 756.00 per clutch
Because the 050440 or 70050440 steering
clutch throw-out bearings were getting s-o-o-o-o expensive, and because pulling and
re-installing these steering clutches a second time is rarely a fun project, we bought a
volume of these bearings so you would not have to cut corners. Now, at $45.00 ea,
you do not have to re-use marginal bearings.
 Steering Clutch Throw-out bearing 050440
(70050440) p/n new $45.00
 Steering Clutch Throw-out Bearing Cage P/N 050249--->70050249
new $145.00
 Steering Clutch Throw-out Bearing 050223
--->70050223
SLEEVE ..NEW...$165.00 EA
  NEW BRAKE
DRUMS!! 050216
--->623779--->647868
P/N BRAKE DRUM $286.00 41 LBS
PART NUMBERS CHANGE TO 70050216
--->70623779
--->70647868
We also have NEW SPRINGS for your steering clutches.
 16.00 ea Steering Clutch Springs P/N 70050236
OR 050236
Lining kits. Set of linings with rivets, for one complete two piece
brake band with width of 2 1/2" width P/N 076552 -->70076552
$55.00
Heavy Duty lining kit option for the 2 1/2" wide
brake bands. Woven linings, interwoven brass threads, designed for severe and
extreme conditions. Will handle high heat (400 degrees) and repeated use without
fade of loss of coefficient of friction. 68.00 per set
One set includes linings for one complete 2 pc band with rivets. ORDER P/N 076552HD
 New brake bands with New Linings 2 1/2 inch wide
(later bands had 4 inch width)
Upper Band 70076427---> 70622823
Lower Band 70076428---> 70622820
Fits all HD5 and EARLY HD6 Crawler Loaders and Dozers.............$255.00 Total For Both
Halves
 HD6/HD6G 4 INCH BRAKE LINING KIT, INCLUDES RIVETS, LINING FOR
ONE BAND ...........$78.00
HEAVY DUTY WOVEN LINING WOVEN WITH BRASS STRANDS, DESIGNED FOR REPEATED USE IN SEVERE
CONDITIONS, ABLE TO WITHSTAND HIGH TEMPERATURE USE (400 DEGREE)WITH MINIMAL LOSS OF
COEFFICIENT OF FRICTION.
BRAKE BAND PINS........DRILLED AND TAPPED 050326-->70050326 70092787
092787
TWO USED PER CLUTCH
$12.50 EA OR $20.00 FOR SET OF 2
 Brake Band Adjusting nuts, with springs, retainers,
roll pin and block New 38.00
ea p/n 079013
The new 050328 Forks
$35.00 ea
NEWER REPLACEMENT ADJUSTING NUTS
NOTE: You may also order the later 090960 adjuster which has
1/2 inch longer threads and used the narrower block 090958
and upgraded spring which comes with the newer adjuster NEW 44.00 Both early and late adjusters use the
same forks.
The new 050328 Forks
$35.00 ea
 THE STANDARD 042122 IS REPLACED BY THE
HEAVY DUTY 082909 CLUTCH
DISC
DISCS NEW FLYWHEEL CLUTCH DISCS FOR AUBURN AND ROCKFORD CLUTCHES
082909>088816
70082909>70088816(FOR
BOTH AUBURN OR ROCKFORD CLUTCHES) $225.00 CURRENTLY OUT OF
STOCK
Auburn clutch levers, new aftermarket p/n 70088815 (088815) or
earlier p/n 70055758 (055758)
@ 35.00 ea
Auburn clutch links, new aftermarket p/n 70055759 (055759) @
18.00 ea
  NEW AUBURN CLUTCH PINS.
p/n's 048173-->70048173
(12 used per clutch) $3.00 ea
052354-->70052354
pins (6 used per clutch) $3.00 ea
NEW HD5 AUBURN FLYWHEEL CLUTCH PRESSURE PLATE P/N 042124---> 70042124 (70088814)
$185.00
 PRESSURE PLATE COMPRESSION SPRINGS...p/n#078278
(70078278) ..Set of Qty 15 @ $24.00
 NEW AUBURN FLYWHEEL CLUTCH RETRACTING SPRINGS
AND RETAINERS. This is another problem you may find when the Auburn clutch needs
repair. 3 of each are used per clutch. For a set of (3) p/n
042130 Springs 15.00/set or for a set of (3) retainers p/n 042129,
$15.00/set
Auburn Flywheel Clutch Sleeve (throw out collar) 078116 (70078116)
For HD5/HD6 Auburn Flywheel Clutches $230.00
Earlier p/n 061137 directly replaced by the 078116 (70078116)
FLYWHEEL CLUTCH BEARINGS. The bearing Block Kits (complete w/ needle bearings
and seals) fit both the Auburn Clutch and the Rockford Clutch. P/n 082877 Block Brg
Kit (
early p/n 053929) $45.00 ea (New) TWO BEARING
BLOCK KITS NEEDED PER CLUTCH
The Throw Out thrust bearings 042994--->621440 fit the
Auburn Clutches......48.00 ea (New)
 P/N 078134 70078134 Auburn Flywheel
Clutch Throw Out Yoke..............NEW $175.00 ( For the
Bearing Block kits,complete w/ needle bearings and seals, the Throw-Out Block Brg
Kit P/n 082877 ( early p/n
053929) $45.00 ea (New) TWO
BEARING BLOCK KITS NEEDED PER CLUTCH
NEW FINAL DRIVE SEALS FOR 6 SPLINED AXLES
SMALL OUTER FINAL DRIVE SEAL KIT P/N 073763 (70073763)
94.00
LARGE INNER FINAL DRIVE SEAL KIT P/N 073762
(70073762) 124.00
 FInal Drive Nut and seal retainer P/N 081369
-->70081369 NEW $90.00
 Final Drive Gear 20 T Pinion, Intermediate shaft P/N 049886---70049886
NEW $270.00
 Final Drive Gear 20 T Pinion, Upper Pinion P/N 049881--->70049881
NEW $240.00
 Transmission
Locking Plunger Boot P/N'S 076845-->080166-->049966
BOOT NEW $11.00
 Transmission Front Seal
Kit 082876
(70082876) NEW $91.00
 Brake control rod BOOT 078908 --->70078908
earlier part numbers 051531 051532 051574
NEW $12.00 ea or $20.00 for Pair
 The following manuals are only
guidelines. Watch your serial numbers closely and when you think you have the
correct information, CHECK AGAIN!!! Allis Chalmers
made some confusing model designations. In the beginning AC made an HD6 and the
standard model, standard gauge, was called HD6B. Do not confuse this HD6B with the
later model HD6B! They are entirely different machines in almost all circumstances.
 SEARCHING FOR PARTS!?
When searching for parts, the part
numbers are, of course, very important. It is GOOD TO KNOW
that the part numbers in your parts manuals are probably NOT
the part numbers that you want to search for!!! If you have a manual showing 6 digit part
numbers, and the early machines and their parts manuals mostly show 6 digit numbers, and
you want to replace a bearing or seal for example, your local bearing and seal house will
not be able to help you if you give them that 6 digit number! For most of the
early construction equipment and loaders you will want to add a "70" in
front of the 6 digit number to make an 8 digit number. Depending on product line,
you may have to add a "73" in front of the 6 digit number. If you give
your local bearing and seal house the 8 digit part number they will be able to help you!
(or if you are doing a Google search) As with most rules, there are always
exceptions but your odds of finding the part that you need greatly increase if you do
follow this rule. "Use
an 8 digit part number by adding a "70" or "73" to your 6 digit
number."
 You do not know what may have been done to your
machine in previous repairs over the decades. Even the manuals are not always
accurate so verify with casting numbers and compare them to part numbers that you find.
HD6 GENERAL SPECIFICATIONS
HD6 OPERATIONS
MANUAL SER#BELOW 13222
HD6
CRAWLER LOADER TS6 OPERATIONS AND PARTS
HD6 OPERATIONS
MANUAL FOR SER#13222-UP
HD6 CRAWLER SERVICE
MANUAL (EARLY)
HD6 CRAWLER
TRACTOR PARTS MANUAL SER# BELOW 13222
HD6 BRAKE PARTS FOR EARLY
HD6
HD6 ENGINE
PARTS BELOW SER#13222
HD6 FINAL DRIVE
PARTS BELOW SER#13222
HD6 FINAL DRIVE
PARTS
HD6 FINAL DRIVE SERVICE
HD6 FLYWHEEL CLUTCH
CONTROL PARTS BELOW SER#13222
HD6 FLYWHEEL CLUTCH
PARTS
HD6 FLYWHEEL CLUTCH
SERVICE
HD6 STEERING CLUTCH PARTS
HD6 STEERING
CLUTCH SERVICE
HD6 TRANSMISSION PARTS
HD6 TRANSMISSION
SERVICE
HD6A-AG-B-E
CRAWLER TRACTOR PARTS MANUAL FOR SER#13222-UP 40M 70C 94S#22251-UP
HD6E
OIL TYPE FLYWHEEL CLUTCH PARTS
HD6E
ENGINE OIL FILTER FOR 13222-UP
HD6E
OIL TYPE BRAKE BAND
HD6E 13222-UP
STEERING CLUTCHES
HD6E 13222-up
HYDRAULIC STEERING PARTS
HD6EP CRAWLER PARTS
MANUAL SER#14484-2250 and 88Y22251-UP INCLUDES DOZER, RIPPER, HYDRAULICS
HD6EP
PARTS FOR STEERING CLUTCH SER# 14400-UP
HD6G TRACK
LOADER PARTS MANUAL SER#101-UP AND 37A22251-UP
HD6G
STEERING CLUTCH PARTS BEFORE SER#13222
HD6G
HYDRAULIC FILTERS BEFORE SER#13222
HD6G
FINAL DRIVE AND BRAKE PARTS AFTER SER#13222
HD6G
FLYWHEEL CLUTCH PARTS, DRY TYPE AFTER SER# 13222
HD6G TRACK
LOADER BEFORE SER#13222 PARTS MANUAL
HD6G TRACK
LOADER AFTER SER#13222 PARTS MANUAL
HD6EP
AND HD7G TRANSMISSION SERVICE MANUAL
LATEST SERVICE MANUAL
FOR THE HD6A HD6S HD6E HD6G HD11A HD11B HD11E HD11G
AND ALSO APPLIES TO THE HD5 AND HD9'S. SERVICE MANUAL FOR STEERING CLUTCHES
VERY GOOD SVC MANUAL
TO
GIVE YOU AN IDEA OF HOW THE
STEERING CLUTCH IS ASSEMBLED AND RE-ASSEMBLED I PUT TOGETHER A PICTURE
ALBUM AND STEP BY STEP EXPLANATION OF THE BASICS. YOU DO NOT NEED TO HIRE IT
DONE...........IT IS REALLY A SIMPLE PROCEDURE AND YOU DO NOT NEED TO HIRE A SHOP TO DO
THE JOB FOR YOU. JUST CLICK
ON THIS PARAGRAPH AND YOU WILL BE DIRECTED TO THE WEB PAGE WITH THE
PICTURES AND EXPLANATIONS.
Click HERE to view all of our new steering clutch
discs.
|
for orders or
questions.
